8 位置 3 排 针座、有护套、 面板安装； 通孔 间距 0.157 英寸(4.00 mm)
General Product Description: AMPSEAL 8-Position Vertical and Right-Angle Header Counterbore Addition Description of Changes The Industrial and Commercial Transportation business unit of TE Connectivity is making a change to the mounting hole geometry on all 8-position vertical and right-angle AMPSEAL headers for the part number(s) listed below. These PNs are TE proprietary designs, therefore considered catalog/general market product. PPAP and/or sample requests must be submitted within 14 days of PCN submission via firstname.lastname@example.org or ePPAP system. Submission will not occur without request. If PPAP requested, disposition response is required within 14 days of submit date or it will be considered approved. Product drawing(s) are affected. Reason for Changes: Product Improvement. Dear Customer, we hereby inform you of this change. The change is necessary to improve mounting capabilities. The change does not impact performance. IMPORTANT: The current and previous revisions of these parts can be used interchangeably in the field. The change(s) are being phased in gradually and previous revision can remain stocked until use. Shipments of both configurations may be mixed.First Date To Ship (Changed Parts Only): 15-SEP-2021Last Date for Mixed Shipments: (Changed Parts Only): 15-MAR-2023
Description of Changes The Industrial and Commercial Transportation business unit of TE Connectivity is making a change to the mounting hole geometry view on the customer drawings for the drawing numbers listed below. The part numbers associated with the drawings are TE proprietary designs, therefore considered catalog/general market product. Reason for Changes: Customer Request. Dear Customer, we hereby inform you of this change. The change is necessary to make the views consistent across all customer drawings. This consistency will aid the customers use of the information in their application development. The change does not impact connector performance.
General Product Description: HEADER ASSEMBLY, 8,14,23,35 POSITION, RIGHT ANGLE, AMPSEAL,VERTICAL,AMPSEAL WITH FLANGE SEAL Description of Changes ZONED7 view the mounting holes, been removed the +/-0.1 tolerance value Reason for Changes: Document Clarification. Dear customer, we are contacting you to notify that there is no change in Form, Fit, Function.
AMPSEAL Sealed Connector System - Header Assembly Description of Changes: The Industrial and Commercial Transportation business unit of TE Connectivity is making a change to the AMPSEAL Header Assembly Customer Drawing notes and dimensions for the part number(s) listed in this notice.These PNs are TE proprietary designs, therefore considered catalog/general market product. TThe change does not affect Form Fit or Function of the AMPSEAL Headers. This change is for notification purposes only and no PPAP is planned or required. Reason for Changes: Customer Request. The change is necessary to clarify the information on mounting screw used on the AMPSEAL Header, to modify the mounting hole location dimensions from reference dimension to a tolerance dimension and the suggested mounting hole dimensions will be expanded to aid in the assembly of the header. The change does not impact performance. IMPORTANT: The current and previous revisions of these parts can be used interchangeably in the field.
Description of Changes The Industrial and Commercial Transportation business unit of TE Connectivity is making a change to shipping location for the part number(s) listed in the attached. There is no change in manufacturing location or product. These PNs are TE proprietary designs, therefore considered catalog/general market product. All products you currently receive from our Tullahoma, TN (USA) location will be transitioned to the new Distribution Center at Greensboro, NC (USA). Reason for Changes: The change is necessary to better serve our customers and as part of our continuous improvement efforts to provide extraordinary Customer Service
AMPSEAL Sealed Connector System - Header Assemblies Description of Changes This PCN is an addendum to previous AMPSEAL PCN numbers E-18-008460 (Future PCN 60454). In an effort to maximize our capacity, our intent is to move the molding of the header housing and the dispensing of the flange seal material on the header assemblies from the current TE molding and assembly manufacturing location to a new single TE manufacturing location in Empalme, Sonora, Mexico. This second TE facility is located in the same compound as the current TE facility.
Ampseal Header Products Description of Changes As part of our continuous improvement efforts to provide extraordinary Customer Service, we are pleased to announce the following: To improve the transit time of products to our mutual end customers, TE Connectivity is changing the distribution location for several products manufactured in Mexico currently stored at our Ontario, California or El Paso, Texas distribution centers. Instead we would like to store in our Hermosillo, Mexico DC ASAP. Customers have the option to pick up in Hermosillo, Mexico or to pick up in Nogales, AZ at our cross-dock. Upon receipt, distributor orders will be tendered to the carrier in line with each distributors Incoterms. The proximity of the Nogales cross dock to our Hermosillo, Mexico site will simplify the flow of products across the border. The longer-term intent will be to distribute from a point in the US due to MFG location change (Reference PCN E-18-008460 for MFG Change) during the latter half of 2019.
Description of Changes:This is an addendum to PCN-18-008460, a copy is attached on this PCN.If the customer requires a PPAP submission, please place the request with email@example.com If there are any further questions or concerns, please contact your TE Sales Contact or Account Manager directly.Reason for Changes: The PPAP submission email address was not included in PCN-18-008460. To aid in customer PPAP receipt, this information is being supplied
Customer drawing PCB layout shows the header pin thru hole at DIA1.38+/-0.10 This hole size is too small for the header pin size and is changing to DIA1.75+/-0.10 Reason For Change: Document Clarification. The current PCB thru hole size is too small for the header pin diameter and is changing to add greater hole clearance. There is no change to the header pin size or the product in general, this is only an information change on the customer drawing
|No of Positions:||8|
|Operating Temp Range:||-40°C to +105°C|
|No of Rows:||3|
|Mating Type:||Locking Ramp|